Vixen 0.71x Focal Reducer for VC200L

Field flattener without reduction factor for Explore Scientific ED80 , ED102 and ED127 APO Refractors The imaging plane of many telescopes is not flat but curved. This means that only the area in the centre is perfectly focused - the edge becomes blurred. The human eye can usually compensate for this image property, but a camera shows increasing blurriness towards the edge of the image field. The Explore Scientific Zero X field flattener eliminates the field curvature in many telescopes with a focal length of approx. 480 to 952 mm. The Zero X field flattener was calculated and developed for Explore Scientific ED80, ED102 and ED127 apochromats with focal ratios of F=6.0 and F=7.5. The image sharpness at the edge is dramatically increased. The stars appear round and no longer distorted - a clear benefit for the whole image aesthetics. The Zero X image flattener can be used not only with Explore Scientific Apos, but also with many other Apos. This flattener does not change the focal length of the telescope. Correction for up to full-frame camera sensors (24x36mm) The Explore Scientific Zero X image flattener has been developed due to the rapid development of ever larger camera sensors. With it, there is finally a field flattener available that illuminates and corrects the field of view for full-frame camera sensors up to 24x36 mm. How to use the Zero X field flattener with M48 thread connection This field flattener has a 2 inch (50.8 mm) plug-in connection on the telescope side, with which it is inserted into the telescope instead of an eyepiece or star diagonal mirror. On the camera side, there is a standardised M48 x 0.75 mm connection thread. This M48 connection thread offers a larger free inner diameter than the usual T2 (M42) thread and prevents vignetting when using large camera sensors. With an optionally available and camera-specific adapter ring, a DSLR camera can be connected to it. The working distance is already set at 55 mm. Of course, mirrorless cameras or special astro cameras can also be used with the M48 thread connection. For this, the appropriate M48 spacer sleeves or adapters are additionally required to set the right working distance of 55 mm. This must always be done with every corrector or field flattener so that the best possible field flattening is achieved.Filter thread on telescope side availableThe telescope-side 2.0 inch plug-in sleeve has an M48x0.75 filter thread (internal thread). Individual 2.0 inch colour or nebula filters can be inserted here to increase the contrast of the images.FEATURESField flattener for Explore Scientific ED80, ED102 and ED127 APO telescopesRemoves field curvature from telescopesProduces round stars even at the edge of the image fieldImage sharpness at the edge is drastically increasedA clear benefit for the whole image aestheticsCorrection of field curvature for up to full-frame camera sensors (24x36 mm)Image field flattener without reduction factorOn the telescope side with 2 inch (50.8 mm) plug-in connection and M48x0.75mm filter threadCamera side with large M48 threaded connectorWorking distance of 55 mm between field flattener and camera sensorFor telescopes with a focal length of approx. 480 to 952 mmOptimised for telescopes with focal ratios from F=6.0 to F=7.5Can also be used for various other APOsFully multi-coating on all lens surfacesHousing made of lightweight aluminium, black anodisedAluminium dust cap for M48 threadSCOPE OF DELIVERYZero X field flattener (1 piece)Dust caps

The EXPLORE SCIENTIFIC 3" 0.7x Reducer/corrector, reduces a compatible telescope's focal length by a factor of 0.7x (for around f/8) and 0.8x (for around f/10) respectively. The reducer/corrector not only reduces the focal length but also flattens the field. Although originally developed for the Explore Scientific ED-APOs 127mm and 152mm, the reducer can be used with many systems - for example with the Explore Scientific ED-APOs 102mm and 165mm (please note, this will not work on the Explore Scientific 80mm ED Apo refractors though). With certain telescope focal lengths, a slight restriction of the correction at the edge of the image field can be expected when using full-frame sensors. This unit comes with 3" barrel adaptor for direct focuser thread M54x0.75 (the standard focuser thread of the Explore Scientific Essential series of ED Apos) and T2 camera adaptor. This reducer/corrector features a free aperture of 65mm, so that it can be used even with cameras that have a large sensor - if the telescope allows for this. Note: As previously mentioned, this Reducer/corrector comes with a screw on ring, which fits the standard focuser thread of the Explore Scientific Essential series of ED Apos. For telescopes which are equipped with the 2.5" HEX Focuser, the optional screw-on adapter part no: 0510366 is needed. Other telescopes, not in the Explore Scientific range, with standard 2" push-fit focusers will need the Explore Scientific 2" Adaptor for 3" Corrector - part no: 0510364 to get this reducer correctly fitted. SPECIFICATIONS Reduces the focal length by 0.7x at f/8 Flattens the field for astrophotography Developed for ED127 und ED152 APO telescopes Also fits Explore Scientific ED102 and ED165 telescopes - and others Free aperture: 65mm Inner thread for telescope adaption: M76x0.75mm Outer thread for camera adaption: M72x0.75mm 3" focuser barrel adaptor included Adaptor for Explore Scientific focuser M54x0.75mm included T2 camera adaptor M42x0.75mm included Diameter: 78.5mm; length: 100mm Length without adaptors: 52mm Weight without adaptors: 530g What's Included Reducer/Flattener 3" focuser barrel adaptor Adaptor for Focuser M54x0.75mm T2 camera adaptor M42x0.75mm Dust caps

Camera specific bayonet adapter (camera ring) for Canon EOS DSLR with M48x0.75 mm internal thread for astrophotography. By using the large thread M48x0.75 mm, the vignetting of e.g. a DSLR full format sensor is effectively avoided. Compared to the small T2 thread M42x0.75, this adapter has a free inner diameter of 47.5 mm. This camera ring is made of matt black anodised aluminium and weighs only 40 grams. The light path (overall length) is 10.0 mm. FEATURES Camera-specific bayonet adapter Canon EOS Large female thread M48x0.75 mm Free inner diameter of 47,5mm No vignetting for full format sensors Light path (overall length) is 10.0 mm Made of matt black anodized aluminium Weight only 40 grams SCOPE OF DELIVERY Camera ring for Canon EOS (1 piece)

The Vixen corrector PH is a 3-element Wynne corrector for demanding applications. Designed for the Vixen R200SS Newtonian reflector, but also suitable for other optics with similar specifications.The optical design consists of 3 lenses in 3 groups. The corrector provides excellent correction of system-induced coma of parabolic mirrors and the resulting spherical aberration. The corrected field has a diameter of 44 mm, making it suitable for the 24x36 mm format (full-frame DSLR/CCD cameras). This guarantees razor-shape images across the entire field. The lens surfaces are coated with a cutting-edge 99.9% anti-reflective AS coating, which is also used for Vixen's flagship VSD100F3.8.Turn your Vixen R200SS reflector telescope into the perfect astrograph!FEATURESPremium coma corrector for the R 200SS Newton refelctor 3 lens systems in 3 groups, guarantees absolute colour purity and sharp stars to the edge of the field of viewImage illumination up to 44 mm for full-frame imagesReduces the focal length of the R 200SS from 800 mm to 760 mm 1:3.8Also suitable for visual observations with an eyepiece adapterWeight: 175 gDELIVERY CONTENTComa correctorDust caps on front and back

High-performance flattener and reducer set connection rings for Vixen telescopes SD81S, SD103S and SD115S, as well as the ED predecessor series. High-performance flattener and reducer set The kit consists of a high-performance flattener, a reducer for reducing the focal length, and connection rings (distance ring SD81, EX Tube 66), which were developed for prime-focus astrophotography with the SD81S, SD103S and SD115S telescopes. The flattener and the 0.79x reducer deliver a significant increase in telescope performance and image quality. You obtain a flat and sharp image until the edges, including with a full-frame DSLR camera. Ultra-sharp image over the entire field of view of the DSLR full-frame sensor The SD flattener improves the image quality to the edge of the field of view without changing the original focal length of the telescope. The field of view of the DSLR camera with a full-frame sensor is fully illuminated (44 mm), ensuring that stars appear sharp until the edges of the image. When used in conjunction with the Reducer HD, the focal length is reduced by a factor of 0.79 (f/7.7→6.1) whilst maintaining the 44 mm illumination. High-contrast AS coating The anti-reflex AS coating, which is also used on our high-end VSD 100 f/3.8 astrograph, delivers a high light transmission of 99.9% per lens surface. Loss of light, ghosting and scattered light images are virtually eliminated thanks to the completely matte interior coating. FEATURES Reduces the focal length by a factor of 0.79 Designed for full-frame cameras High-contrast AS coating Ultra-sharp image over the entire field of view Designed for full-frame DSLR cameras Illumination: 44 mm Correct distance to chip: 63.5 mm Designed for the SD81S, SD103S and SD115S Also suitable for the ED81S, ED103S and ED 115S DELIVERY CONTENT SD Flattener HD Reducer HD Adapter ring for SD81 66 mm EX extension tube Dust caps

The image plane of many telescopes is not plane, but curved. This results in a picture that has its optimal focus only in the center of the field of view - the edge of the field is out of focus and thus unsharp. The human eye is able to accomodate most of this but a camera will show stars that get increasingly unsharp towards the edge of the field. The Explore Scientific Multi Purpose Curvature Corrector eliminates field curvature in a variety of telescopes - Explore Scientific Apos and many other refractors and cassegrain telescopes. This increases the edge sharpness in the image drastically. Improves edge sharpness not only with Explore Scientific Apos, but also with many other refractor and cassegrain telescopes. This image field leveller fits all Canon EOS cameras, but can also be used for other camera types due to the universal T2 thread connection. This requires an optional camera-specific T2 ring. SPECIFICATIONSImage flattener for Canon EOS cameras Eliminates the field curvature of ED APO telescopes Can also be used for various cassegrains The image sharpness at the edge is drastically increased 2 inch/50.8mm push-in connector with filter thread T2 threaded connection (M42x0,75mm) Full multi-coating on all lens surfaces Stainless steel housingAdapter for Canon EOS bayonet included DELIVERY SCOPE Bildfeldebner Canon EOS (1 piece)

After three years of testing and refining we are extremely proud to present the new Explore Scientific High Resolution (HR) Coma Corrector. This corrector is a class of it´s own - it is fully functional for visual use and expands the focal length by only 6%! The Explore Scientific Coma Correktor is delivered as a complete set together with a rotating helical focuser with laser-etched scale, so you get a full package: corrector, adaptor to T2 (M42x0.75mm), adaptor to M48 (M48x0.75) and the helical focuser for visual fun. This coma corrector really is "high resolution" - it deliveres a visual polystrehl performance of 0,98 at f/4 and 0,96 at f/3! So it can stay in the telescope - and you will not only enjoy a tack-sharp Jupiter, but aslo sharp and defined moons in the future! What this means in terms of performance is shown in the three pictures with the graphs - the sharpness increase in those comparisons with and without corrector are stunning (examples are 400mm f/4, f/3,5 and f/3). Please notice: These graphs are for FLAT FIELD! You will get this performance without refocussing! Diameter of the field is 30mm - it doesn´t make sense to increase this with 2" and fast optical systems. Length of the 2" corrector barrel is approx. 85mm and it can be used with almost all 2" focusers on the market. To use the HR Coma Corrector visually, you need to have at least 32mm spare inward travel at your focuser, while the focus is on the same plane as the focusers end. Photographically there is no problem - the HR Coma Corrector shifts the focus outward by about 35mm, so that you will have no problem in achieving focus, when you are able to focus your camera without the HR Coma Corrector. FEATURESEliminates coma, field-curvature and astigmatism in newtonians Diffraction limited performance on axis and in the field Flattens the field Works for very fast systems down to f/3 Four-lens construction Can be used with almost all 2" focusers on the market SCOPE OF DELIVERY High Resolution (HR) Coma Corrector Adaptor to T2 (M42x0.75mm) Adaptor to M48 (M48x0.75) Helical focuser

Five extension tubes from 30 to 5mm length with thread connection M48x0,75mm in a set. For adjusting different distances of the camera to the focal plane of the telescope or the corrector/field flattener. There is an M48.0,75 internal and external thread in each individual tube. The M48x0.75 thread is also called large T2 photo thread or 2.0 inch filter thread. Camera specific bayonet adapters or color and nebula filters can be used. Included are 5 different tubes with the steps 30, 20, 15, 10 and 5 mm. The larger free inner diameter of 45.0 mm effectively prevents undesired vignetting of the camera sensor. The outer diameter of the sleeves is exactly 50.65 mm and can therefore be mounted directly in any 2 inch diameter eyepiece adapter. FEATURES Extension sleeves M48x0,75 in set Five extension sleeves: 30, 20, 15, 10, 5 mm Use with correctors and field flatteners Distance adjustment from camera to focal plane Suitable for camera-specific bayonet adapters Also suitable for 2.0 inch colour and nebular filters Internal and external thread M48x0.75 mm (large T2 thread) Large inner diameter of 45.0 mm Outer diameter is 50.65 mm (2 inches) Black matt anodized aluminium Total weight 85 grams SCOPE OF DELIVERY Extension sleeves M48x0.75 (5 pieces)

This adaptor enables you to connect the 0510360 0.7x focal reducer/field flattner to telescopes that feature the 2.5" Hexafoc. The big inner diameter of the 2.5" Hexafoc is fully utilised with this adaptor to avoid vignetting.What's Included1x Hexafoc 2.5 adaptor for 3" 0.7x Corrector ring

The image plane of many telescopes is not plane, but curved. This results in a picture that has its optimal focus only in the center of the field of view - the edge of the field is out of focus and thus unsharp. The human eye is able to accomodate most of this but a camera will show stars that get increasingly unsharp towards the edge of the field. The Explore Scientific Multi Purpose Curvature Corrector eliminates field curvature in a variety of telescopes - Explore Scientific Apos and many other refractors and cassegrain telescopes. This increases the edge sharpness in the image drastically. Improves edge sharpness not only with Explore Scientific Apos, but also with many other refractor and cassegrain telescopes. This image field leveller fits all Nikon DSLR cameras, but can also be used for other camera types due to the universal T2 thread connection. This requires an optional camera-specific T2 ring. SPECIFICATIONSImage flattener for Nikon DSLR cameras Eliminates the field curvature of ED APO telescopes Can also be used for various cassegrains The image sharpness at the edge is drastically increased 2 inch/50.8mm push-in connector with filter thread T2 threaded connection (M42x0,75mm) Full multi-coating on all lens surfacesStainless steel housing Adapter for Nikon F bayonet included DELIVERY SCOPE Bildfeldebner Nikon (1 piece)

Above-average contrast The Reducer HD features the optical coating that was developed by Vixen for our high-end VSD100F3.8 astrograph. The AS coating provides light transmission of up to 99.9% per lens surface. The special matte surface in the interior also minimizes ghosting, light loss and lens flares. Reducer HD in combination with SD telescopes The Reducer HD can be used on telescopes from the SD series (SD81S, SD103S and SD113S) with the SD Flattener HD Kit (item #37246) . The Reducer HD reduces the focal length by a factor of 0.79x (f/7.7 to f/6.1) and delivers a razor sharp image over the entire 44 mm image sensor surface on DSLR cameras. Reducer HD in combination with AX103S and VC200L telescopes In addition to the SD telescopes, the Reducer SD is also compatible with the AX103S and VC200L telescopes. With these telescopes, the focal length is reduced by a factor of 0.77x.FEATURESUp to 99.9% light transmission per lens surfaceReduces the focal length by a factor of 0.79xAlso suitable for full-frame DSLR camerasFor the ED/SD 81S, 103S, 115SAS coating with light transmission of up to 99.9% DELIVERY CONTENTVixen Reducer HDDust caps

​High quality SD field flattener HD kit for the Vixen ED and SD refractor telescopesWith this image field plane you get razor-sharp star images up to the edge of the field of view.The flattener illuminates a 44 mm image circle and is therefore also suitable for full format cameras.The same anti-reflection AS coating that is also used for Vixen's high-end astrograph VSD 100 f / 3.8 enables a high light transmission of 99.9 percent per lens surface. Loss of light, ghosting and stray light images are almost completely eliminated by the completely matt interior coating.Can be used on the SD81S, SD103S and SD 115S, as well as the predecessor ED seriesAlso requires the Wide Photo Adapter and a T2 ringWeight 218 g