Trigger cable CN3 for Canon

This release cable was developed for taking time-lapse recordings with the POLARIE U Star Tracker and a DSLR camera. In combination with an app specially developed for the POLARIE U, you can simply set up an exposure control via WIFI, controlling your exposures very easily using your smartphone.REQUIREMENTPOLARIE U Star Tracker, smartphone with the POLARIE U Control app and release cable for your cameraPROPERTIESLocking cable for Canon, Fujifilm, Olympus, Pentax, SamsungConnection to the POLARIE U: 2.5 mm stereo mini plugConnection to the camera: 2.5 mm stereo mini plugCoiled cable length: 20 cm to 50 cmWeight: 26 gWHAT'S INCLUDED:Release cable

Attachment plates, such as the ARCA SWISS are compatible with this quick-release panorama plate. (Note: angle plate is not included in # 35527). The base of the Vixen Quick Release Panorama Clamp can be rotated 360 degrees so that the position of the mounted camera system can be adjusted simply by loosening the clamping lever. In addition to the recommended Vixen dovetail bar DD and top plate, the camera mount is also compatible with other devices with 1/4 ", 3/8" inch screws. The recommended accessory is the X000096 Angle L Bracket for portrait and landscape photography. PROPERTIES Can be rotated 360 degrees ARCA SWISS compatible Weight: 320g WHAT'S INCLUDED Quick-release panorama plate Screws and tools

The Vixen POLARIE Multi Mounting Block was developed to fit Vixen profile dovetail rails, such as the Vixen Dovetail Slide Bar DD, to the Polarie Star Tracker. In this way you can increase the load capacity of the tracker up to 6.5 kg! By releasing the clamping lever on the multiple assembly block, you can move the dovetail freely and clamp it again, making balancing of your camera or telescope rig an easy task. The hole in the middle of the multiple mounting block enables the photographer to carry out the polar alignment without removing the POLARIE polar finder PFL with the dovetail rail DD or the dovetail rail PG. Using one of these combinations, you can easily put deep sky photography into practice with a telephoto lens, or compact telescope. PROPERTIES Allows the inclusion of dovetail rails The Star Tracker can hold up to 6.5 kg in weight Allows the use of telephoto lenses Polar alignment possible without removing the polar finder Weight: 440g WHAT'S INCLUDED POLARIE multiple assembly block Assembly tool

This T2 ring allows you to use your Sony camera on a telescope or microscope with a T2 thread.Depending on the mode, you may require an additional camera adapter.FEATUREST-2 ring for connecting an SLR cameraDesigned for Sony EWeight: 113 gDELIVERY CONTENTT-2 Ring Sony E

You need this Vixen polar finder set for the POLARIE U Star Tracker in order to be able to align the POLARIE U exactly to the celestial pole. This is very important for longer focal lengths and exposure times, in order to obtain point-like star images. The polar finder enables polar alignment with an accuracy of 3 arc minutes . The polar alignment is very simple: You only have to bring the Pole Star and two other stars into the field of view of the polar finder and rotate them with the stars so that they are congruent with the reticule shown in the polar finder.  No further calculation is needed - no time and date to set, just match the reticule to the polar stars and get imaging. The polar finder PF-L II has red, dimmable lighting that switches itself off after a few minutes in order to save the batteries.PROPERTIES5 x 20 viewfinder with 10 ° field of view3 star positioningNorthern skies: Polaris, Delta UMI, 51 CepSouthern skies: Chi Octantis, Tau Octantis, Sigma OctantisDimmable, red lighting in 8 levelsWHAT'S INCLUDEDPole finder PF-L IIMounting armCR 2032 battery

The BRESSER UV + IR Cut Filter makes lunar and planetary images even sharper.Digital astro cameras have a wide sensitivity range that significantly exceeds the spectrum of visible light. Thus, the wavelengths of invisible light in the ultraviolet and infrared are also captured. This leads inevitably to a small additional and of course unwanted blur. The solution is this UV + IR Cut Filter, which allows only light in the visible range 400 nm to 680 nm to pass through and blocks all other wavelengths of light. As soon as these disturbing light waves are cut off, the sharpness of the image and the contrast are increased. Suddenly, details on the surface of Jupiter, for example, can be seen that were previously only barely visible. A clear plus, which can be achieved by this filter.Suitable for BRESSER CMOS cameras and other manufacturers with female camera thread M30 x 0.75 mmAfter removing the original screw adapter with sensor protection glass, the BRESSER UV + IR Cut filter is mounted to the camera instead. This filter has a fine M30 x 0.75 mm external thread for mounting on the camera. The exchange is therefore quick and easy. On the opposite side, i.e. on the telescope side, there is a standard C-mount female thread for mounting other accessories. Note: This filter does not have a standard 1.25 inch (31.7 mm) filter thread. FEATURESBRESSER UV + IR Cut Filter for photographyWavelengths of invisible light in ultraviolet and infrared are blockedPasses only visible light in the range 400nm to 680nmLunar and planetary images become even sharperSuitable for BRESSER CMOS cameras an othersMale fine thread M30 x 0.75mm for mounting on the camera housingC-Mount internal thread for mounting further accessories Quick and easy mounting of the filterGlass filter made of fine optical glassPlane-parallel polished and multiple layer coatedFilter housing made of matt black anodized aluminumHousing outer diameter 31.7mm (1.25 inch)Diameter of free light transmission 17.0mm (1.25 inch) SCOPE OF DELIVERYUV + IR Cut Filter (1 pc)