EXPLORE SCIENTIFIC ED APO 80mm f/6 FCD-1 Alu 2" R&P Focuser

Field flattener without reduction factor for Explore Scientific ED80 , ED102 and ED127 APO Refractors The imaging plane of many telescopes is not flat but curved. This means that only the area in the centre is perfectly focused - the edge becomes blurred. The human eye can usually compensate for this image property, but a camera shows increasing blurriness towards the edge of the image field. The Explore Scientific Zero X field flattener eliminates the field curvature in many telescopes with a focal length of approx. 480 to 952 mm. The Zero X field flattener was calculated and developed for Explore Scientific ED80, ED102 and ED127 apochromats with focal ratios of F=6.0 and F=7.5. The image sharpness at the edge is dramatically increased. The stars appear round and no longer distorted - a clear benefit for the whole image aesthetics. The Zero X image flattener can be used not only with Explore Scientific Apos, but also with many other Apos. This flattener does not change the focal length of the telescope. Correction for up to full-frame camera sensors (24x36mm) The Explore Scientific Zero X image flattener has been developed due to the rapid development of ever larger camera sensors. With it, there is finally a field flattener available that illuminates and corrects the field of view for full-frame camera sensors up to 24x36 mm. How to use the Zero X field flattener with M48 thread connection This field flattener has a 2 inch (50.8 mm) plug-in connection on the telescope side, with which it is inserted into the telescope instead of an eyepiece or star diagonal mirror. On the camera side, there is a standardised M48 x 0.75 mm connection thread. This M48 connection thread offers a larger free inner diameter than the usual T2 (M42) thread and prevents vignetting when using large camera sensors. With an optionally available and camera-specific adapter ring, a DSLR camera can be connected to it. The working distance is already set at 55 mm. Of course, mirrorless cameras or special astro cameras can also be used with the M48 thread connection. For this, the appropriate M48 spacer sleeves or adapters are additionally required to set the right working distance of 55 mm. This must always be done with every corrector or field flattener so that the best possible field flattening is achieved.Filter thread on telescope side availableThe telescope-side 2.0 inch plug-in sleeve has an M48x0.75 filter thread (internal thread). Individual 2.0 inch colour or nebula filters can be inserted here to increase the contrast of the images.FEATURESField flattener for Explore Scientific ED80, ED102 and ED127 APO telescopesRemoves field curvature from telescopesProduces round stars even at the edge of the image fieldImage sharpness at the edge is drastically increasedA clear benefit for the whole image aestheticsCorrection of field curvature for up to full-frame camera sensors (24x36 mm)Image field flattener without reduction factorOn the telescope side with 2 inch (50.8 mm) plug-in connection and M48x0.75mm filter threadCamera side with large M48 threaded connectorWorking distance of 55 mm between field flattener and camera sensorFor telescopes with a focal length of approx. 480 to 952 mmOptimised for telescopes with focal ratios from F=6.0 to F=7.5Can also be used for various other APOsFully multi-coating on all lens surfacesHousing made of lightweight aluminium, black anodisedAluminium dust cap for M48 threadSCOPE OF DELIVERYZero X field flattener (1 piece)Dust caps

Universal 50mm viewfinder and guide telescope with a focal length of 220mmExcellent 8x50 viewfinder telescope with removable eyepiece unit and crosshairs with adjustable red illumination. The precise helical focuser and the 1.25 inch /31.7mm plug-in connection, as well as the T2 camera connection thread (M42x0.75mm), allow the autoguiding required for long time exposure to obtain a point-shaped star image. It can also be used as a mini travel telescope.High quality 8x50 viewfinder telescope with adjustable crosshair illuminationImage sharpness and viewing characteristics lift this viewfinder well above the level of the usual 8x50 viewfinder scopes. The visible image is bright and crisply sharp. Furthermore, this viewfinder has a very large field of view (FOV) of 6.96 degrees. This makes finding and adjusting objects much easier. The existing scale markings (pitch=1 degree) on the crosshairs are a good reference for estimating distances, and the open centre markings also make it easier to centre objects precisely. All lens surfaces are protected against weathering by multi-coating and guarantee a bright viewfinder image due to the high light transmission values. The adjustable red LED illumination unit is powered by two LR41 coin batteries. The main lens and the crosshairs can be focused independently of each other, giving you perfect focus for your eyes.Compact tracking unit for autoguidingOne of the main applications for this telescope is the so-called autoguiding. Here the usually larger photo-taking optics are actively corrected by a smaller guiding telescope with a second tracking camera. This means that the mechanical fluctuations in the tracking accuracy, which are present in all astronomical telescope mounts, are measured by the tracking camera and compensated accordingly. This is necessary in order to obtain a point-shaped star image on the astrophotos during long time exposures and to avoid unwanted star trails. For this purpose, the guiding telescope is inserted into the existing viewfinder shoe of the photo-taking optics and aligned parallel. If the existing viewfinder shoe is not compatible, a suitable viewfinder shoe is also included. With the 1.25 inch / 31,7mm plug connection at the rear end or via T2 thread connection (M42x0,75mm), a tracking camera can be mounted afterwards. This is held securely by a brass ring clamp and 3 clamping screws. Please note the required back focus for your tracking camera. The focal plane (backfocus) is approx. 22mm behind the T2 thread. The sensitive focusing on the guiding star is done by a large knurled wheel of the mechanically precise manufactured helical focuser. For easy reproduction of the point of focus, this has a white millimetre scale from 0 to 28mm, which is attached by laser engraving. After the tracking camera has been connected directly or via computer to the telescope mount and the necessary basic settings have been made, the first astrophotos with long time exposure can be taken.Use as mini travel telescopeThis viewfinder and guide telescope can also be used quite simply as a mini travel telescope. With the optional eyepieces, a magnification of 8x to 40x can be achieved. Nearly all eyepieces with a focal length of 5 to 26mm and 1.25 inch/31.7mm plug connection are suitable. Especially recommended are the EXPLORE SCIENTIFIC eyepieces of the 52 degree (Art. 02195xx) and 62 degree (02196xx) LER series. Note: Only straight view use is possible.Metal viewfinder holder and viewfinder shoeThe mount of this viewfinder and guide telescope is completely made of aluminium and is a stable base. The viewfinder mount is suitable for many common types of telescopes, such as EXPLORE SCIENTIFIC, BRESSER MESSIER etc. If the existing viewfinder shoe is not compatible, a matching viewfinder shoe is also included. This can be attached to the telescopic tube by means of four M5 screws. The bore distances of the viewfinder shoe are 31.7mm on the longitudinal and transverse axis. The six large adjustment screws with non-slip knurling make it easy to align the viewfinder, even with clammy fingers. All adjusting and clamping screws have plastic tips that effectively prevent the viewfinder housing and viewfinder mount from being scratched.FEATURESExcellent 8x50 viewfinder and guiding telescopeCan also be used as mini travel telescopePerfect image sharpness and good viewing comfortFMC Multi-coated lens surfacesLens focal length: 220mmMax. possible camera weight: 550gRemovable eyepiece/cross hair unitCamera connection via 1.25 inch / 31.7mm plug connection or T2 threadT2 thread: M42 x 0,75mmPrecise helical focuser for focusing the visible imageFocuser travel range: 28mmClose focus distance: 3 mLaser engraved millimetre scale from 0 to 28mm on the focuserFocal plane (backfocus) is approx. 22mm behind the T2 threadSeparate focusing of the crosshair at the eyepieceVery large field of view FOV of 6.96 degreesWith adjustable red cross-hair iillumination Scale markings crosshair with 1.0 degree graduationPower supply of illumination unit: coin battery type LR41 (2pcs)Brass ring clamp and 3 clamping screws on the 1.25 inch plug connectionWith optional eyepieces magnifications from 8x to 40x can be achievedSuitable are almost all eyepieces with 1.25 inch/31,7mm shaftMounting of the viewfinder telescope is completely made of aluminiumViewfinder mount with 6 large adjustment screws with knurled head for easy gripFinder shoe suitable for EXPLORE SCIENTIFIC, BRESSER MESSIER etc.Additionally a suitable viewfinder shoe is includedBore distances of the viewfinder shoe are 31.7mm on the longitudinal and transverse axisAdjusting and clamping screws have plastic tipsSCOPE OF DELIVERY8x50 viewfinder/guiding telescopeEyepiece unit with crosshairCrosshair illumination unit incl. batteriesViewfinder holder with viewfinder shoeInstruction manual

Universal 60mm viewfinder and guide telescope with a focal length of 250mmExcellent 10x60 viewfinder telescope with removable eyepiece unit and crosshairs with adjustable red illumination. The larger aperture and focal length, provide an even brighter field of view and more accurate tracking due to the higher resolution. The precise helical focuser and the 1.25 inch /31.7mm plug-in connection, as well as the T2 camera connection thread (M42x0.75mm), allow the autoguiding required for long time exposure to obtain a point-shaped star image. It can also be used as a mini travel telescope.High quality 10x60 viewfinder telescope with adjustable crosshair illuminationImage sharpness and viewing characteristics lift this viewfinder well above the level of the usual 10x60 viewfinder scopes. The visible image is bright and crisply sharp. Furthermore, this viewfinder has a very large field of view (FOV) of 6.0 degrees. This makes finding and adjusting objects much easier. The existing scale markings (pitch=0.85 degree) on the crosshair are a good reference for estimating distances, and the open centre markings also make it easier to centre objects precisely. All lens surfaces are protected against weathering by multi-coating and guarantee a bright viewfinder image due to the high light transmission values. The adjustable red LED illumination unit is powered by two LR41 coin batteries. The main lens and the crosshairs can be focused independently of each other, giving you perfect focus for your eyes.Compact tracking unit for autoguidingOne of the main applications for this telescope is the so-called autoguiding. Here the usually larger photo-taking optics are actively corrected by a smaller guiding telescope with a second tracking camera. This means that the mechanical fluctuations in the tracking accuracy, which are present in all astronomical telescope mounts, are measured by the tracking camera and compensated accordingly. This is necessary in order to obtain a point-shaped star image on the astrophotos during long time exposures and to avoid unwanted star trails. For this purpose, the guiding telescope is inserted into the existing viewfinder shoe of the photo-taking optics and aligned parallel. If the existing viewfinder shoe is not compatible, a suitable viewfinder shoe is also included. With the 1.25 inch / 31,7mm plug connection at the rear end or via T2 thread connection (M42x0,75mm), a tracking camera can be mounted afterwards. This is held securely by a brass ring clamp and 3 clamping screws. Please note the required back focus for your tracking camera. The focal plane (backfocus) is approx. 22mm behind the T2 thread. The sensitive focusing on the guiding star is done by a large knurled wheel of the mechanically precise manufactured helical focuser. For easy reproduction of the point of focus, this has a white millimetre scale from 0 to 28mm, which is attached by laser engraving. After the tracking camera has been connected directly or via computer to the telescope mount and the necessary basic settings have been made, the first astrophotos with long time exposure can be taken.Use as mini travel telescopeThis viewfinder and guide telescope can also be used quite simply as a mini travel telescope. With the optional eyepieces, a magnification of 9x to 50x can be achieved. Nearly all eyepieces with a focal length of 5 to 26mm and 1.25 inch/31.7mm plug connection are suitable. Especially recommended are the EXPLORE SCIENTIFIC eyepieces of the 52 degree (Art. 02195xx) and 62 degree (02196xx) LER series. Note: Only straight view use is possible.Metal viewfinder holder and viewfinder shoeThe mount of this viewfinder and guide telescope is completely made of aluminium and is a stable base. The viewfinder mount is suitable for many common types of telescopes, such as EXPLORE SCIENTIFIC, BRESSER MESSIER etc. If the existing viewfinder shoe is not compatible, a matching viewfinder shoe is also included. This can be attached to the telescopic tube by means of four M5 screws. The bore distances of the viewfinder shoe are 31.7mm on the longitudinal and transverse axis. The six large adjustment screws with non-slip knurling make it easy to align the viewfinder, even with clammy fingers. All adjusting and clamping screws have plastic tips that effectively prevent the viewfinder housing and viewfinder mount from being scratched.FEATURESExcellent 10x60 viewfinder and guiding telescopeCan also be used as mini travel telescopePerfect image sharpness and good viewing comfortFMC Multi-coated lens surfacesLens focal length: 250mmMax. possible camera weight: 550gRemovable eyepiece/cross hair unitCamera connection via 1.25 inch / 31.7mm plug connection or T2 threadT2 thread: M42 x 0,75mmPrecise helical focuser for focusing the visible imageFocuser travel range: 28mmClose focus distance: 3 mLaser engraved millimetre scale from 0 to 28mm on the focuserFocal plane (backfocus) is approx. 22mm behind the T2 threadSeparate focusing of the crosshair at the eyepieceVery large field of view FOV of 6.0 degreesWith adjustable red cross-hair iillumination Scale markings crosshair with 0,85 degree graduationPower supply of illumination unit: coin battery type LR41 (2pcs)Brass ring clamp and 3 clamping screws on the 1.25 inch plug connectionWith optional eyepieces magnifications from 9x to 50x can be achievedSuitable are almost all eyepieces with 1.25 inch/31,7mm shaftMounting of the viewfinder telescope is completely made of aluminiumViewfinder mount with 6 large adjustment screws with knurled head for easy gripFinder shoe suitable for EXPLORE SCIENTIFIC, BRESSER MESSIER etc.Additionally a suitable viewfinder shoe is includedBore distances of the viewfinder shoe are 31.7mm on the longitudinal and transverse axisAdjusting and clamping screws have plastic tipsWHAT'S INCLUDED10x60 viewfinder/guiding telescopeEyepiece unit with crosshairCrosshair illumination unit incl. batteriesViewfinder holder with viewfinder shoeInstruction manual

BRESSER EXOS-2 GoTo Equatorial Mount. Mount, tripod and hand box with computer. This German mount has tracking motors in both axes that follow celestial objects very precisely.The handbox with GoTo works reliable and controls the mount in every situation. Precise ball bearings in both axes ensures minimal backlash at all nine possible tracking speeds.The battery pack (12 V) is conveniently fastened to the tripod shelf and takes eight size "D" batteries.The mount rests on a very tough and rigid stainless steel tripod and can take optical tubes of up to 13 kg. GOTO - Stargazing at the push of a button! The Startracker GoTo System enables beginners to start astronomical observations in just a few minutes, and guides you to objects that are hard to localize through a standard finder scope.Just push the button and the GoTo System will find planets, nebulae or galaxies for you and position your telescope automatically and precise.The GoTo System database includes thousands of astronomical objects.The Messier mount with GoTo System allows you to observe without tedious searching, or image faint objects that are hard to find in a standard finder scope.The BRESSER StarTracker GoTo systems uses servo motors for both axes and features an ST-4 compatible autoguiding input. Guiding aggressivity can be set on the mount itself. The menu navigation of the Startracker Handbox is also multilingual and offers the settings of German, English, French, Spanish and Italian.CHARACTERISTICS MOUNT Stable parallactic mount with fine drive in both axes Ball bearings in both axes for more precise movements Stable height adjustable stainless steel tripod ( Min. 69cm / Max. 109,5cm ) Load capacity up to 13 kg payload Circular bubble for easy horizontal alignment GoTo Mount with motors and hand box controller, for easy finding and guiding moon, planets, stars and much more ST-4 compatible autoguider interface Pole height scale for setting the latitude Scaled graduated circular rings to facilitate finding objects using a star atlas or planetarium software Pole finder scope with optional illumination ( item no. 4964212 ) Tripod weight: 4.7 kg Mount weight: 6.7 kg (without counterweight) Total weight incl. counterweight: 15.9 kg Batteries: not included SCOPE OF DELIVERY Equatorial EXOS 2 GOTO mount with stainless steel tripod and Startracker handcontroller Adjustable polar finder scope with optional illumination Stainless steel tube field tripod with accessory tray 1 x 4.5 kg counterweight

The Twilight I is a light-to-medium-duty alt-azimuth mount with tripod designed to quickly and easily accept small to medium sized refractors, such as the AR102 + AR127s or ED102mm + ED127, and of course, the ED80mm. Lightweight, fast Newtonians will also match up nicely with the BRESSER Twilight I mount. As long as your telescope does not exceed 18 pounds and has a Vixen-Style Universal Dovetail bar for mounting the telescope to the mount head, you are good to go. The Twilight I alt-azimuth mount head is made of powder-coated aluminum and there are worm gears on both axes. The adjustable angle head can be tilted forward or back at a 45° angle to allow more clearance for your telescope so you can point it straight up for viewing at the zenith. The Allen hex wrench for doing the mount head adjustment can be safely stored at the integrated magnetic holder.  Slow-motion control cables are attached on the vertical and horizontal axes, and are easy to turn during the night, even with gloves on, due to the over-sized knurled knobs that are attached to the end of each cable. They can be attached to either side of each axis to accommodate right or left-handed users, or different types of telescopes (e.g. refractors vs. Newtonian reflectors) for ease of adjustment. The stainless steel tripod that comes standard with the Twilight I mount has adjustable legs and a wide foot print of 42 inches, which makes the tripod more stable. A spreader bar locks against the inside of the legs to secure the tripod even further, and keep vibrations to a minimum. SCOPE OF DELIVERYTwilight I Telescope MountStainless Steel Field tripod

Mount and Tripod. The BRESSER Messier beginners series of telescopes. Within this series you find smaller optics mounted stable on the new BRESSER EXOS 1 mount. This combination means more value for money and puts an end to flimsy beginners scopes which discourage most of the beginners due to small, under engineered mounts. The EXOS 1 with a robust stainless steel tripod bears optical tubes weighing up to 7kg stable for visual observation. The optional motor drive for the RA axis makes usage even more comfortable, so there is no need of manual tracking and the object is kept steadily in the field of view.FEATURES Stable parallactic mount with fine drive in both axes Circular bubble level for easy horizontal alignment Stable height-adjustable stainless steel tripod Retrofittable with a tracking motor for the right ascension axis Pole height scale for setting the latitude Scaled graduated circular rings for easier finding of objects by means of star atlas or planetarium software Tripod weight: 4.7 kg Mount weight: 4 kg (without counterweight) Total weight incl. counterweight: 13.2 kg SCOPE OF DELIVERYEXOS 1 German equatorial mountstainless steel tube field tripod1 x 4.5 kg counterweight

You see better with two eyesThe BRESSER BinoViewer Deluxe makes it possible to observe astronomical objects in a relaxed way with both eyes and with considerably more detail than using one eye. The images created of the moon, planets and globular clusters are particularly impressive. But also with deep-sky objects such as the Orion Nebula the detection of details is much easier. At the same time this binoviewer is very easy to handle. Thanks to the newly patented optical system you can get into focus with any telescope. All you need is a pair of identical eyepieces to enjoy this dramatic and immersive viewing experience.How to use the BinoViewer? Since the BRESSER BinoViewer Deluxe does not require an additional light path (back focus), it can be used with any telescope - including Newtonians and short focus refracting telescopes, which traditionally suffered when using standard binoviewers. No light path corrector or similar accessory is necessary. If a standard 1.25'' eyepiece can be focused, the binoviewer will also work. The eyepiece focal length and field of view size of the eyepieces used are fully retained. As with binoculars one eyepiece is focused first using the telescope focuser. Then the second eyepiece can be brought into focus using the helical focuser on the binoviewer. The required interpupillary distance is then elegantly adjusted to a range of 58–74mm with the help of a linear sliding mechanism, with graduated marker, to help you find your ideal interocular setting quickly.  Self-centring helical eyepiece grips, rather than side-mounted thumbscrew eyepiece retainers are used, decreasing the chance of offsetting collimation of both eyepiece to each other.  The fact that this design of binoviewer uses a well-engineered linear slide mechanism to adjust interpupillary distance, rather than a cheaper-to-produce traditional hinged design also helps retention of collimation.Which objects can be observed with this accessory?Actually, all objects that were previously observed with the telescope in question, but only monocularly with one eye. Because there is no magnification factor at the binoviewer, even low magnifications can be achieved. This makes not only the moon, planets and globular clusters, but also the brighter deep-sky objects very interesting observation targets. The use of two eyes leads to a more relaxed view than using one eye alone.  Although true depth of field viewing at infinity is a little beyond most telescopes and binoviewers, users will note how the human brain attempts to impose depth of field ("3d-like") effects on stereo views through binoviewers.  The biggest difference that most observers comment upon when comparing views through binoviewers like these, as opposed to single monocular eyepiece views, is the extra detail that can be seen in most observable targets.  Relaxed viewing and extra detail in objects are the two main benefits of binoviewing, which the BRESSER Bino Viewer Deluxe 1.25'' delivers in abundance.Also ideal as an accessory for solar telescopesA very special application is the use of the BRESSER BinoViewer Deluxe in combination with all solar telescopes. The spherical shape of the sun with all its surface details is shown very impressively.  The depth of field effects of seeing filaments silhouetted against the solar surface are particularly enjoyable to observe.Important note: Do not use the BRESSER Binoviwer Deluxe without a suitable solar telescope or a safe solar filter in front of the telescopes objective lens . Otherwise, there is an acute risk of going blind.High-quality mechanics and materialsThe entire BRESSER BinoViewer Deluxe is made of high-quality materials. Except for the outer plastic covers all components are made of anodised aluminium. Particularly remarkable are the low-backlash sliding mechanism for adjusting the interpupillary distance and the precise rotary clamping of both eyepiece adapters. The wide clamping surface holds the eyepieces in place securely and also centres them automatically on the optical axis. The one-sided dioptric adjustment has a backlash-free helical drive and enables the finest corrections. For safe transport a high-quality hard-shell transport case is included in the scope of delivery.Which eyepieces can be used?All eyepieces with a 1.25'' barrel and a field stop of up to 22mm. Depending on the interpupillary distance the outer diameter of the eyepiece housing should not exceed a value of approximately 50 mm.Filter thread 1.25'' availableNo 2nd filter sets are necessary to operate the BRESSER Binocular Approach Deluxe. The desired colour or nebula filter can be screwed directly into the 1.25'' nosepiece. in this configuration, when changing the eyepieces to affect a change in magnification, no swapping of filters is necessary.  Unique mirror-lens system with Ohara (Japan) lanthanum glass material The BRESSER Binocular Viewer Deluxe is equipped with a unique mirror-lens system. This has the advantage of higher light transmission and less color aberration. The resulting image is simply brighter and sharper. To achieve this the exclusive Ohara (Japan) lanthanum glass material has been used and in addition all optical surfaces are equipped with a full multi-layer broadband coating. Finally the beam-splitting mirror has a 99% dielectric coating and completes the excellent optical design.FEATURESEnables binocular observations with all telescopesRelaxed and comfortable viewingThree-dimensional viewing experienceSuitable for all telescopes with 1.25'' eyepiece connectionNo additional light path requiredNo magnification factor at the binocular attachmentEven low magnifications with large fields of view are achievableFor observing moon, planets and deep sky objectsPrecise and robust mechanicsSliding mechanism to adjust the interpupillary distanceDioptric compensation via fine helical driveWide eyepiece rotation clamp with automatic centeringFilter thread 1.25'' (M28.5 x 0.6mm) availableLens and mirror design made of finest Ohara (Japan) lanthanum glass materialAdvanced broadband multilayer coating on all optical surfaces99 % dielectric-coated beam-splitting mirrorHigh-quality hard-shell carrying case includedWHAT'S INCLUDEDBino Viewer DeluxeDust capsCarrying case 

The Explore Scientific Two Room Pop-Up Observatory is a useful weatherproof tent that protects your valuable equipment from wind, dew, rain and dust. Most amateur astronomers and astrophotographers dream of having an observatory to keep dust, dew and wind away from their telescope and to shield disturbing stray light from their telescope's optics. But for many astronomers, an observatory is only a dream because of the cost of a roll-roof building or an observatory dome. There is also the problem that an observatory building needs a permanent location that is suitable for an observatory. Portable, quick to set up and inexpensive A good solution is a portable observatory tent. Compared to their fixed counterparts, a tent is extremely inexpensive and can be set up almost anywhere there is a flat surface and a clear view of the sky. However, setting up a portable observatory tent can also be a hassle. No one wants to waste their valuable observing time reading complex instructions while trying to figure out which pole goes where. For this reason, we have used a sturdy pop-up design. Setting up the EXPLORE SCIENTIFIC Pop-Up Observatory can be done in a matter of minutes. By releasing a retaining strap, the complete tent unfolds from its packaging in just a few seconds. You really don't need to do anything other than connect the two observatory rooms with a Velcro seam and attach it to the ground. Thanks to this simple design, the EXPLORE SCIENTIFIC Pop-Up Observatory can be set up and taken down in just a few minutes, giving you plenty of time to enjoy your astronomy weekend. Plenty of space for your equipment and super compact when folded up. With just under 5 square metres of total space and 1.52 metre high side walls, coupled with 1.83 metre high windscreens, the EXPLORE SCIENTIFIC Pop-Up Observatory allows you to set up your computer equipment in one room and the telescope in the other, or set up two complete telescope systems. Each room is 152 by 152 centimetres. Mobile observatory with compact transport dimensions In addition to being easy to set up and take down, another advantage of the pop-up design is that it is travel-friendly, as it is light and easy to stow away. The entire observatory tent folds down to a package 70 centimetres in diameter and 10 centimetres thick. This allows it to be transported in a small car or even on a flight for distant expeditions. And apart from the fact that it allows you to go to your favourite observing site at any time, portable observatory tents are usually the first choice for astronomers and astrophotographers attending star party events.  Advanced materials provide optimal protection and durability However, the fact that the EXPLORE SCIENTIFIC Pop-Up Observatory is lightweight and easy to store and set up doesn't mean it can't withstand bad weather conditions. The Black-Out coated polyamide material is waterproof and offers excellent UV protection. This guarantees reliable protection for your equipment as well as long-lasting durability of the observatory tent. Large doors for convenient use The doors to enter the observatory tent and pass through the attached rooms are very generously sized at 102 centimetres high and 92 centimetres wide, so you can easily walk in and through your equipment. The doors roll down to keep moisture out and their heavy-duty zips will last for years. The extra weather cover protects your gear when not in use. With the large weather cover included, you can protect your gear from the hot sun or a surprise rain shower during the day. Or even from dew at night. The modern, coated and waterproof material keeps all unwanted weather influences away from your equipment. Included are cords and pegs to tie down the tent. The structure also has additional holding straps for the use of heavy-duty straps, which can be purchased at local hardware stores. PRODUCT VIDEO:  https://youtu.be/1rL5PzPa-dQ FEATURESPractical weather protection for telescopes Protects your equipment from wind, dew, rain and dust Mobile observatory: portable, quickly assembled, reasonably priced Compact transport size also suitable for air travel 5 square metres of space for your equipment and sufficient freedom of movement Interior dimensions: 152 x 304cm Side wall height 152cm / windbreak wall height 183cm Large 102 x 92cm doors for ease of use Additional weather protection cover included Advanced materials provide optimum protection and durability Cords and pegs included to tie down the tent Additional tie downs for heavy duty straps included Transport dimensions and weight: diameter 70cm, height 10cm, 3kg Colour tent material: black SCOPE OF DELIVERY Two-room pop-up observatory tent Weather protection cover Set of cords and pegs

One of the most important obstacles for the exploration of the night sky is the brightening of the night sky by artificial lights, such as streetlights. The night sky is not really dark in the vicinity of towns or cities, which reduces the visibility of objects beyond the solar system enormously. Depending on the type of the celestial object, it is possible to dramatically increase the contrast by blocking annoying artificial light. The EXPLORE SCIENTIFIC UHC filter "zeros in" on the wavelengths of so-called emission nebulae. Those objects glow in special colours - their emission lines. Those emission lines are linked to chemical elements - in this case hydrogen at 486nm and 656nm, plus oxygen at 496nm and 501nm. The EXPLORE SCIENTIFIC UHC nebula filter blocks all other colour wavelengths (and thereby nearly all of artificial light) and only the emission line of the hydrogen and oxygen can pass the filter. The result is astonishing: suddenly nebulae are visible at locations that were completely invisible from, without filters. In suburban skies, for example the Owl-nebula M97, the Veil-nebula NGC 6992 or even the bright Dumbell-nebula M27 are not clearly visible. Using this filter allows you to see nebulae and their structures in much finer detail. A must for every visual observer. The Explore Scientific nebula filters come with a individual test certificate - your guarantee to receive a premium filter.

One of the most important obstacles for the exploration of the night sky is the brightening of the night sky by artificial lights, such as streetlights. The night sky is not really dark in the vicinity of towns or cities, which reduces the visibility of objects beyond the solar systems enormously. Depending on the type of the celestial object it is possible to increase the contrast dramatically by blocking the annoying artificial light. The EXPLORE SCIENTIFIC O-III filter uses a characteristic property of the so called emission nebulae. Those objects glow in special colours, the so called emission lines. Those emission lines are linked to chemical elements - in this case oxygen. The EXPLORE SCIENTIFIC O-III nebula filter blocks all other colours (and thereby nearly all of the artificial light) and only the two emission lines of the oxygen can pass the filter. The result is astonishing: suddenly nebulae are visible at locations that were completely empty without filters. In suburban skies for example the veil nebula NGC 6992 is almost not visible with a 200mm telescope. By using this filter you can see the nebula and its structures without problems. A must for every visual observer. The EXPLORE SCIENTIFIC nebula filters come with a individual test certificate - your guarantee to receive a premium filter.FEATURESenables the observation of so called emission nebulaeblocks almost the entire artificial lightonly the two emission lines of ionised oxygen passes the filterWHAT'S INCLUDED1x 2" O-III nebula filter

This Herschel wedge is designed for superior White-Light solar observing and imaging. It can be used with refracting telescopes up to 102mm aperture, with 1.25'' focuser. This complete system comes with installed ND3.0 filter.Herschel Wedges are used to observe the sun in White Light. Around 95% of the Sun's light is suppressed by the wedge's ceramic prism. The remaining sun light is dimmed further by a factory-installed ND3.0 grey filter. Lunt Solar Systems Herschel wedges are installed in a fully closed housing with integrated heat trap. No stray light can escape from this, therefore it is very safe method of observing our nearest star.The difference between Herschel-wedges and normal front mounted filters is that the filtering takes place just before the eyepiece or camera. This provides better contrast and sharpness of the solar image - with more surface detail visible as a result.  Furthermore, a Herschel wedge is inherently safer than at a front mounted filter. A Herschel wedge can not rip or become punctured like a foil filter can be and it cannot become detached from the telescope objective accidentally.Only for use with refractor telescopes up to 102mm aperture:Because the full energy and heat of the sun inside the telescope, we advise solely using refractors for Herschel-wedge use. The refractor must not have corrector lenses at the back. Optical elements like corrector lenses, or secondary mirrors of reflecting telescopes, could suffer from thermal build-up by concentrated solar energy and could be permanently damaged.Tuning the brightness:Because the Herschel-wedge produces polarised light, you can use a normal polarising filter at the eyepiece, or camera-adapter. By turning the polarising filter the image brightness can be varied to the user's liking.This additional Polarising filter is not included. We recommend the BRESSER 1.25'' polarising filter, no: 4946464.FEATURESFor refractor telescopes up to 102mm apertureConnection to telescope: 1.25''Connection to eyepiece: 1.25''90° housing like star-diagonalEspecially high-quality optical surfaces for very good contrastFully closed housing with integrated heat trapNo stray light escaping - therefore it is very safeThe needed ND3.0 filter is fix installedWHAT'S INCLUDEDHerschel-wedge for 1.25'' focuserIntegrated ND3.0 filterTransport caseInstruction manual

An amici prism allows for a comfortable 90° viewing position and creates an erect image without left-right reversal. This makes it especially suitable for nature observations but it can also be very helpful with astronomical observations. Particularly beginners may find it easier to orientate in the sky when they compare the view through the telescope with what they can see with their naked eyes.With this  amici prism an astronomical telescope can be used as a powerful spotting scope.Suitable for refractor telescopes as well as Maksutov-Cassegrain style telescopes with 1,25" visual back.FEATUREScomfortable eye relief for refractor telescopes90°- viewing position and image without left-right reversalastronomical telescope turns to a powerful spotting scope1,25" visual backfully multicoated prismSCOPE OF DELIVERYAmici Prism 90° 31.7mm/1.25"

Enables you to connect a camera to telescopes that accept 2" barrel eyepieces. You will need a T2-ring for your special camera type also. The very special feature of this adaptor is the very short mechanical design (2.0mm) which enables the camera use also on telescopes with a short focal range. This adapter is also prepared to use with 2" filters.   

With teleextenders it is possible to extend the effective focal length of a telescope system, resulting in higher magnification for the observation of the moon, the planets or small Deep-Sky objects with the same eyepieces. So you can use the advantages of eyepieces with longer focal length - such as the bigger eye distance and the more relaxed observing comfort - at high magnifications also.These teleextenders incorporate a telecentric optical design that deliveres a excellent image sharpness over the whole field of view and are premium choices for visual observations and astrophotography. The combination of excellent fully multicoating with superior optical design makes the Focal Extenders superior to classic Barlow lenses.FEATURES: Suitable for visual observations and astrophotographyDoubling the effective total focal length of the telescopeFour lens telecentric design Fully multicoatedFilter thread for color or nebula filtersSCOPE OF DELIVERY: Fokal Extender 2 x Adapter 2" (50,8mm) auf 1,25" (31,7mm)

With teleextenders it is possible to extend the effective focal length of a telescope system, resulting in higher magnification for the observation of the moon, the planets or small Deep-Sky objects with the same eyepieces. So you can use the advantages of eyepieces with longer focal length - such as the bigger eye distance and the more relaxed observing comfort - at high magnifications also.These teleextenders incorporate a telecentric optical design that deliveres a excellent image sharpness over the whole field of view and are premium choices for visual observations and astrophotography. The combination of excellent fully multicoating with superior optical design makes the Focal Extenders superior to classic Barlow lenses.FEATURESSuitable for visual observations and astrophotographyTriples the effective total focal length of the telescopeFour lens telecentric designFully multicoatedFilter thread for color or nebula filtersSCOPE OF DELIVERY Fokal Extender 3 x Adapter 2" (50,8mm) auf 1,25" (31,7mm)

If a observing session is a relaxing and joyful experience is heavily dependend on the choice of eyepieces. People wearing glasses very often have the problem to see the entire field of view when they are using eyepieces with large apparent fields. This problem is now history. The new 62°- LER eyepieces by Explore Scientific do not only offer excellent image sharpness and high resolution and contrast over the full field of view - you can see that full field without problems even with glasses on. Fatigue due to tense head positioning and strained viewing simply does not happen because of the excellent viewing comfort these eyepieces provide even to observers wearing glasses. Enjoy the unique combination of excellent image sharpness out to the edge of the field even for fast optics, superior contrast and unmatched viewing comfort. Eyepieces with perfect combinations of various modern glass substrates and highest standards in manufacturing, quality control and service are a tradition at Explore Scientific - the outstanding resolution and sharpness to the very edge.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The rubber inlet and the foldable eyecups make handling and using in the field easy. The patentet EMD"-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Eye relief: 13mm

If a observing session is a relaxing and joyful experience is heavily dependend on the choice of eyepieces. People wearing glasses very often have the problem to see the entire field of view when they are using eyepieces with large apparent fields. This problem is now history. The new 62°- LER eyepieces by Explore Scientific do not only offer excellent image sharpness and high resolution and contrast over the full field of view - you can see that full field without problems even with glasses on. Fatigue due to tense head positioning and strained viewing simply does not happen because of the excellent viewing comfort these eyepieces provide even to observers wearing glasses. Enjoy the unique combination of excellent image sharpness out to the edge of the field even for fast optics, superior contrast and unmatched viewing comfort. Eyepieces with perfect combinations of various modern glass substrates and highest standards in manufacturing, quality control and service are a tradition at Explore Scientific - the outstanding resolution and sharpness to the very edge.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The rubber inlet and the foldable eyecups make handling and using in the field easy. The patentet EMD"-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Eye relief: 12mm

If a observing session is a relaxing and joyful experience is heavily dependend on the choice of eyepieces. People wearing glasses very often have the problem to see the entire field of view when they are using eyepieces with large apparent fields. This problem is now history. The new 62°- LER eyepieces by Explore Scientific do not only offer excellent image sharpness and high resolution and contrast over the full field of view - you can see that full field without problems even with glasses on. Fatigue due to tense head positioning and strained viewing simply does not happen because of the excellent viewing comfort these eyepieces provide even to observers wearing glasses. Enjoy the unique combination of excellent image sharpness out to the edge of the field even for fast optics, superior contrast and unmatched viewing comfort. Eyepieces with perfect combinations of various modern glass substrates and highest standards in manufacturing, quality control and service are a tradition at Explore Scientific - the outstanding resolution and sharpness to the very edge.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The rubber inlet and the foldable eyecups make handling and using in the field easy. The patentet EMD"-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Eye relief: 11mm

If a observing session is a relaxing and joyful experience is heavily dependend on the choice of eyepieces. People wearing glasses very often have the problem to see the entire field of view when they are using eyepieces with large apparent fields. This problem is now history. The new 62°- LER eyepieces by Explore Scientific do not only offer excellent image sharpness and high resolution and contrast over the full field of view - you can see that full field without problems even with glasses on. Fatigue due to tense head positioning and strained viewing simply does not happen because of the excellent viewing comfort these eyepieces provide even to observers wearing glasses. Enjoy the unique combination of excellent image sharpness out to the edge of the field even for fast optics, superior contrast and unmatched viewing comfort. Eyepieces with perfect combinations of various modern glass substrates and highest standards in manufacturing, quality control and service are a tradition at Explore Scientific - the outstanding resolution and sharpness to the very edge.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The rubber inlet and the foldable eyecups make handling and using in the field easy. The patentet EMD"-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Eye relief: 22mm

If a observing session is a relaxing and joyful experience is heavily dependend on the choice of eyepieces. People wearing glasses very often have the problem to see the entire field of view when they are using eyepieces with large apparent fields. This problem is now history. The new 62°- LER eyepieces by Explore Scientific do not only offer excellent image sharpness and high resolution and contrast over the full field of view - you can see that full field without problems even with glasses on. Fatigue due to tense head positioning and strained viewing simply does not happen because of the excellent viewing comfort these eyepieces provide even to observers wearing glasses. Enjoy the unique combination of excellent image sharpness out to the edge of the field even for fast optics, superior contrast and unmatched viewing comfort. Eyepieces with perfect combinations of various modern glass substrates and highest standards in manufacturing, quality control and service are a tradition at Explore Scientific - the outstanding resolution and sharpness to the very edge.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The rubber inlet and the foldable eyecups make handling and using in the field easy. The patentet EMD"-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Eye relief: 28.mm

The visual effect of these new 4,5mm 82° LER eyepieces with their long eye-relief and their 82° apparent field is truly a full-immersion experience.  Your eye is relaxed, allowing you to easily use the "averted vision" technique to study faint details across a huge field-of-view. The 82° Series eyepieces come with foldable eyecups make handling and using in the field easy. As experienced astronomers know, eye comfort is critical when trying to observe at the visual limits of the telescope. To keep internal reflections to a minimum, all internal surfaces of the eyepiece barrel are flat black, as well as the edges of the lenses themselves to minimize the scattering of light within the lenses themselves.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The patented EMD"-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Comfort, Quality, Value. The Explore Scientific 82° LER Series Most short focal length eyepieces are excellent flat-field multi-element oculars that can transform your visual astronomy experience.  These extreme wide field eyepieces are optimized to produce high contrast and high resolution characteristics.SPECIFICATIONSLarge eye distance, large field and great image sharpnessExcellent viewing position for people with glassesExcellent field sharpness even with fast optics82° apparent field of viewArgon-purging prevents internal fogging, the sealing facilitates cleaningPatented EMD-coating to maximize contrastBlackened lens edges to avoid reflexesAll eyepieces of this series are parfocalStainless steel barrel with conical security cutoffDust covers and protective bag includedSCOPE OF DELIVERY82° EyepieceDust coversProtective bag

The visual effect of these new 6,5mm 82° LER eyepieces with their long eye-relief and their 82° apparent field is truly a full-immersion experience.  Your eye is relaxed, allowing you to easily use the averted vision technique to study faint details across a huge field-of-view. The 82° Series eyepieces come with foldable eyecups make handling and using in the field easy. As experienced astronomers know, eye comfort is critical when trying to observe at the visual limits of the telescope. To keep internal reflections to a minimum, all internal surfaces of the eyepiece barrel are flat black, as well as the edges of the lenses themselves to minimize the scattering of light within the lenses themselves.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The patented EMD-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Comfort, Quality, Value. The Explore Scientific 82° LER Series Most short focal length eyepieces are excellent flat-field multi-element oculars that can transform your visual astronomy experience.  These extreme wide field eyepieces are optimized to produce high contrast and high resolution characteristics.SPECIFICATIONSLarge eye distance, large field and great image sharpnessExcellent viewing position for people with glassesExcellent field sharpness even with fast optics82° apparent field of viewArgon-purging prevents internal fogging, the sealing facilitates cleaningPatented EMD"-coating to maximize contrastBlackened lens edges to avoid reflexesAll eyepieces of this series are parfocalStainless steel barrel with conical security cutoffDust covers and protective bag includedSCOPE OF DELIVERY82° EyepieceDust coversProtective bag

The visual effect of these new 8,5mm 82° LER eyepieces with their long eye-relief and their 82° apparent field is truly a full-immersion experience. Your eye is relaxed, allowing you to easily use the averted vision technique to study faint details across a huge field-of-view. The 82° Series eyepieces come with foldable eyecups make handling and using in the field easy. As experienced astronomers know, eye comfort is critical when trying to observe at the visual limits of the telescope. To keep internal reflections to a minimum, all internal surfaces of the eyepiece barrel are flat black, as well as the edges of the lenses themselves to minimize the scattering of light within the lenses themselves.These eyepieces are the choice for observers wearing glasses - with excellent performance and durability. The patented EMD-coating produces high contrast images and prevents reflexes and ghosting. The argon purging effectively prevents internal fogging, and you don´t have to deal with dirt, fungus or cleansing fluids getting between the lenses. The eyepieces are sealed - this makes sure you will be able to enjoy these eyepieces for many years to come.Comfort, Quality, Value. The Explore Scientific 82° LER Series Most short focal length eyepieces are excellent flat-field multi-element oculars that can transform your visual astronomy experience. These extreme wide field eyepieces are optimized to produce high contrast and high resolution characteristics.SPECIFICATIONSLarge eye distance, large field and great image sharpnessExcellent viewing position for people with glassesExcellent field sharpness even with fast optics82° apparent field of viewArgon-purging prevents internal fogging, the sealing facilitates cleaningPatented EMD-coating to maximize contrastBlackened lens edges to avoid reflexesAll eyepieces of this series are parfocalStainless steel barrel with conical security cutoffDust covers and protective bag includedSCOPE OF DELIVERY82° EyepieceDust coversProtective bag

Extension tube with 2" plug diameter and an extension factor of 35mm. A ring clamp ensures an optimal attachement of 2" accessories. The blackened and ridged inside effectively prevents reflections. Also a 2" filter thread is inside.