LUNT Grease for Pressure-Tuner at MT & THa solar telescopes

​Spare part for blocking-filters from LUNT SOLAR SYSTEMS, suitable for B400, B500, B600, B1200 and B1800 blocking-filters.The H-alpha telescopes and filter systems from Lunt Solar Systems each include a blocking-filter. The blocking-filters have a blue colored filter part on the side facing the telescope. This blue colored filter parts may become a milky white layer at older blocking-filters if the blocking-filter was storded at high air humidity for some time. Please always store H-alpha telescopes and filters as dry as possible. If this blue colored filter part has become a milky white layer, it can be replaced with this spare part. The replacement is easy and can be done by the user himself. Installation instructions can be found here under the "Manuals" tab as a PDF for download.Please note that this replacement part can only be used on Lunt Solar Systems blocking-filters B400 to B1800. If the problem happens with the large B3400 blocking-filter, the B3400 must be sent to our service department for repair.FEATURESDiameter: 20mmCannot be used separately, only as spare part at blocking-filters from Lunt Solar SystemsFor B400, B500, B600, B1200 and B1800 blocking-filtersIt does not matter if the blocking-filters are installed in 90° zenith-mirrors or straight extension-tubesSCOPE OF DELIVERYSpare part 20mm blue glass for B400 to B1800 blocking-filters

Spare part for Pressure-Tuner of MT and THa series H-alpha solar telescopes from LUNT SOLAR SYSTEMSTwo rubber O-rings are installed into the Pressure-Tuner of Lunt Solar Systems solar telescopes to seal the air-pressure tuning system. Over time, the rubber of this O-rings can age and become porous, whereby the air-pressure can then no longer be maintained. When this happens, a old O-ring can be replaced by this spare part. The replacement is simple and can be done by the user. Installation instructions can be found here under the tab "Manuals" as a PDF file for download.Please be sure to note:Depending on the production series, the diameters of the Pressure-Tuner pistons can vary slightly. There are pistons for O-rings with 32mm inner diameter and 40mm outer diameter, and pistons for O-rings with 34mm inner diameter and 42mm outer diameter. Please check the diameter of your old O-rings, this spare part is an O-ring with 34mm inner diameter and 42mm outer diameter.If you need the smaller O-ring with 32mm inner diameter and 40mm outer diameter, this is the spare part with item number 0558330.The LS50THa telescopes have Pressure-Tuners with smaller diameters, for these you will need replacement O-rings with item number 0558320.After replacing a O-ring, the piston and cylinder of the Pressure-Tuner can be re-greased with grease available under item number 0558350.FEATURESInner diameter: 34mmOuter diameter: 42mmCannot be used separately, only as a replacement part on the Pressure-Tuner of MT and THa telescopes from Lunt Solar Systems.It does not matter what blocking-filter is at the MT or THa telescope.SCOPE OF DELIVERYSpare part one O-ring with 34mm inner diameter and 42mm outer diameter for Pressure-Tuner of MT and THa H-alpha solar telescopes from Lunt Solar Systems

​Spare part for Pressure-Tuner of LS50THa H-alpha solar telescopes from LUNT SOLAR SYSTEMSA rubber O-ring is installed into the Pressure-Tuner of Lunt Solar Systems LS50THa solar telescopes to seal the air-pressure tuning system. Over time, the rubber of this O-ring can age and become porous, whereby the air-pressure can then no longer be maintained. When this happens, the old O-ring can be replaced by this spare part. The replacement is simple and can be done by the user. Installation instructions can be found here under the tab "Manuals" as a PDF for download.After replacing the O-ring, the piston and cylinder of the Pressure-Tuner can be re-greased with grease available under part number 0558350.Please note that this spare part can only be used on the Lunt Solar Systems LS50THa H-alpha solar telescopes. If the problem occurs on the larger THa or MT series telescopes, the larger O-rings with part numbers 0558330 or 0558340 must be used there.FEATURESInner-diameter: 31mmOuter-diameter: 39mmCannot be used separately, only as a replacement part on the Pressure-Tuner of the LS50THa telescopes from Lunt Solar Systems.It does not matter what blocking filter is at the LS50THaSCOPE OF DELIVERYSpare part one O-ring for pressure tuner of LS50THa

Spare part for Pressure-Tuner of MT and THa series H-alpha solar telescopes from LUNT SOLAR SYSTEMSFor example, if the O-rings have been changed on a Pressure-Tuner of a Lunt Solar Systems H-alpha solar telescope, the Pressure-Tuner can be re-greased with this grease. The grease can be applied to the piston with the O-rings and to the threads of the brass cylinder on the Pressure-Tuner. It keeps the Pressure-Tuner running smoothly and seals it.Please note:Do not use too much grease inside the brass cylinder. The grease must not get into the air passage at the bottom of the brass cylinder, otherwise the Etalon could be damaged in the worst case.FEATURESLithium grease with Teflon contentVery good sealing propertiesHigh adhesion and good corrosion protectionTemperature stable from -20 to +120° CelsiusConstant viscosity during temperature fluctuationsSCOPE OF DELIVERYSpare part: Grease for Pressure-Tuner of MT and THa H-alpha solar telescopes from Lunt Solar Systems

The new BRESSER Super Plössl Eyepiece in a 4 lens design provides good edge definition in a great field of view and a convenient eye relief. The high-grade coating prevents reflections efficiently. Every eyepiece is equipped with rubber eyecups.FEATURESPremium grade optical glassIndividually tuned, multi-layered coatings for maxim Lens edges and all internal metal surfaces are blackened to maximize image -contrast um light transmissionParfocal - little or no refocusing required when switching eyepiecesLong eye reliefAdjustable rubber eyeguards

Spare part for Pressure-Tuner of MT and THa series H-alpha solar telescopes from LUNT SOLAR SYSTEMSTwo rubber O-rings are installed into the Pressure-Tuner of Lunt Solar Systems solar telescopes to seal the air-pressure tuning system. Over time, the rubber of this O-rings can age and become porous, whereby the air-pressure can then no longer be maintained. When this happens, a old O-ring can be replaced by this spare part. The replacement is simple and can be done by the user. Installation instructions can be found here under the tab "Manuals" as a PDF file for download.Please be sure to note:Depending on the production series, the diameters of the Pressure-Tuner pistons can vary slightly. There are pistons for O-rings with 32mm inner diameter and 40mm outer diameter, and pistons for O-rings with 34mm inner diameter and 42mm outer diameter. Please check the diameter of your old O-rings, this spare part is an O-ring with 32mm inner diameter and 40mm outer diameter.If you need the larger O-ring with 34mm inner diameter and 42mm outer diameter, this is the spare part with item number 0558340.The LS50THa telescopes have Pressure-Tuners with smaller diameters, for these you will need replacement O-rings with item number 0558320.After replacing a O-ring, the piston and cylinder of the Pressure-Tuner can be re-greased with grease available under item number 0558350.FEATURESInner diameter: 32mmOuter diameter: 40mmCannot be used separately, only as a replacement part on the Pressure-Tuner of MT and THa telescopes from Lunt Solar Systems.It does not matter what blocking-filter is at the MT or THa telescope.SCOPE OF DELIVERYSpare part one O-ring with 32mm inner diameter and 40mm outer diameter for Pressure-Tuner of MT and THa H-alpha solar telescopes from Lunt Solar Systems